The Trailair Flex Air 5th Wheel Pin Box part # LC328492 is designed to replace a Lippert 1621 pin box. Therefore, it will have have about the same overall dimensions as the pin box it replaces. This will be the case for pretty much any pin box which replaces a Lippert 1621 pin box. If you are trying to lower the nose of the trailer and have made all the adjustments you can to the pin box/hitch, the only option is to raise the trailer which I recommend using the Tandem Axle Lift Kit part... view full answer...
I looked up the hitch weight of your Tracer 24DBS by Primetime and it is 629 lbs dry/unloaded. So for the best weight distribution that would be rated well for that you'd want the Reese Strait Line part # RP66084 which has a rating of between 600 to 1,200 and has best sway control at stopping sway before it starts. view full answer...
If you used a dual hitch adapter like the part # D210 you can carry a cargo carrier like the # FHG77ZR in the upper hitch opening and then tow a trailer with the ball mount platform underneath it. view full answer...
Yes, the picture for the Dexter Disc Brake Kit # K71-638-639 is correct - it comes with one set of brakes. This is how we sell our brake sets so users can purchase them per axle. Since you need 2 sets you'll need to change the quantity to 2 prior to ordering. view full answer...
You will need a different converter charger if you are going to lithium batteries, which is what I believe you are asking. The right one will depend on how many amp hours you need though, like the 100 amp-hour # 34282738. I have added a link below to our selection of lithium batteries as well as a solar calculator which will help you determine how many amp hours you need if you are unsure.
Then for a lithium converter charger we have the Progressive Dynamics 9300 Series RV Converter Charger... view full answer...
Hello George. I can confirm that yes, the Dexter Trailer Hub and Drum Assembly # 42866UC3-EZ will indeed fit your Lippert 7K axle. I was able to get ahold of Lippert and they confirmed the following specs for your axle:
7K
Inner race - 25520
Inner bearing - 25580
Outer race - 14276
Outer bearing - 14125A
Grease seal - 2.250 Inch I.D. - 3.376 Inch O.D. view full answer...
After replacing The Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS, and the motor still does not open the lid you will need to replace the motor. The Replacement 12-Volt Variable Speed Fan Motor for MaxxAir MaxxFan RV Roof Vents # MA10-20968 will replace the 12-volt DC variable-speed fan motor on your MaxxFan 4791KS.
I attached a review video link below. view full answer...
The closest thing that we have to replace your 3-1/4" wet bolts is the Spring-Eye Bolt with Locknut for Slipper Springs # 166079 which measures 3-1/2" long and has a 9/16" diameter. This is a regular bolt without the grease fitting so you'll want to remove the bolts and grease them manually as opposed to pumping grease into them through the fitting.
The only bolt we have that measures 3-1/4" is part # 7-7-6-11 but it only has a 5/16" diameter so it is really only meant for the open end... view full answer...
The Furrion RV Refrigerator # FCR14ACBQABL is rated for 1.268 kWh/24h which is the equivalent of 1,268 Watts so I recommend going with at least the Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch # PD64FR which is rated for 2,000 Watts.
The beauty of this inverter is that is has a built-in transfer switch so you'll actually be connecting both your battery bank and your shore power wiring to this unit and it will automatically pull power from shore power when you're connected... view full answer...
We have 50 amp to 50 amp extension cords like the part # A10-5025E which is 25 feet long and has 90 degree connectors on each end. I am not sure what length you are looking for but I attached a link to a page that has all of the options we have which there are several options. view full answer...
The 5th Airborne Premium 5th Wheel Air Ride King Pin w/ Sidewinder and Turret, # RP61412 has a universal locking wedge included that fits most 5th wheel hitches, some hitches from other manufacturers may require a custom wedge. view full answer...
Yes, it's pretty common for slide toppers to fit right next to patio awnings. Basically you just need 5 to 7 inches of clearance on either side of the slide out for the awning to fit. To pick out a slide topper you would need to measure width of your slide out including the flange.
For example the part # LCV000163287 that you referenced fits slide outs that are between 80 and 85 inches. view full answer...
I like the Curt Adjustable Width Trailer Hitch Receiver, # C13704. This adjustable trailer receiver hitch is designed can be bolted to the vehicle frame or welded on for a no-drill application. It fits widths from 22" to 66" so very adjustable to wide range of applications and has a max tongue weight of 500 lbs. The main hitch body tube can be trimmed so the ends are flush with the frame brackets.
For a bike rack rated for use with a travel trailer, I suggest the Yakima OnRamp Bike... view full answer...
It looks like per the specifications for your 2019 Highland Ridge, Mesa Ridge 2710RL travel trailer. that it measures 31'5" from pin to rear but in order to confirm the correct cover, you will want to measure per the attached diagram instead.
The best cover available to keep out UV rays, protect from wind, and of course the damaging effects of moisture is the ADCO All-Climate # AD27ZR which keeps 99.8 percent of harmful UV rays and 98 percent of dirt and dust particles from reaching trailer... view full answer...
Since the Hopkins kit has LEDs the best option for an observation system would be the Furrion kit part # FRC12TA-BL which has night vision without LEDs, can be on all the time like you want, and has the best reception/signal. view full answer...
To add disc brakes to your 2018 Highland Ridge Open Range Travel Trailer you'll need the following:
- Hydrastar Electric Over Hydraulic Actuator # HBA16
- Kodiak Hydraulic Brake Line Kit # 20TA-BLKIT
- Dexter Disc Brake Kit # K71-638-639 (standard 25580 inner and 15123 outer bearings)
OR
- Dexter Disc Brake Kit # K71-647-648 (42 mm Dexter Nev-R-Lube spindle)
The Hydrastar actuator is the most reliable we have to offer and when you combine it with the Kodiak flexible brake lines and... view full answer...
The best cover for your 2020 Highland Ridge Mesa Ridge MF384RLS that you have is the Adco Aquashed part # 290-52258 which is the correct size, is the easiest to install, and offers the best protection in winter climates. view full answer...
Yes if you wanted to install the Electric Jack w/ Footplate # EJ-3520-BBX that you referenced turned at a different angle you certainly could since the bolt pattern allows for that. view full answer...
Based on the brackets you have near the suspension of your Open Range 3X 375RDS 5th wheel trailer your best option for a shock kit will be a Lippert kit that doesn't take up as much space as the Roadmaster kit you referenced.
For that you'd want the # LC281255 for if your trailer has 3,500 lb axles that are 2-3/8 inch in diameter or the part # LC281281 which fits axle diameters of 3 inch like what are found on 5,200 to 7,000 lb axles.
Also thanks for clarifying what the brown foam was.... view full answer...
Go To Results